Custom Ball valve type underfloor heating manifold

Home / Product / Trap / Ball valve type underfloor heating manifold
Ball valve type underfloor heating manifold
  • Ball valve type underfloor heating manifold

Features

Ball valve type underfloor heating manifold

Trap Number of branch pipelines: 2-6 road
Maximum working temperature: 95℃ 
Working pressure: 1.25Mpa 
Branch distance: 45-55mm 
Competent caliber: G1" G1"1/4 
Matching pipe diameter: ø1216 ø1620 
Matching interface type: Card sleeve type
Specification: 1216×1"(2-12) 1620×1"(2-12) 1216×1"1/4(2-12) 1620×1"1/4(2-12)

Product Parameter

Product Name: Ball valve type copper pipe water separator (ball valve body)
Material: The main raw material of the copper pipe connector is HPb58-2 bar material, and the specification range is Ф16~Ф100 to produce different types of products. The metal content of the material ratio is as follows: Cu 57~61% Pb0.8~2.5% Zn36~40%, impurity content range: Sn, P, Mn, Fe, Ni, Mg, As, Sb, Al, S total not allowed to exceed 2% is recognized by the non-ferrous industry as the best raw material for the manufacture of various valves, pipe connections, precision instruments, and watch parts.
Application range: It is widely used in the pipeline system of cold, hot water, acid, alkali, salt and other liquids and gas, oxygen, compressed air and other media.

Schematic diagram of installation of water separator and water collector Schematic diagram of the installation section of the water separator and water collector
Construction process of floor heating
  •  floor elevation leveling line      
  •  clean up the floor, leveling
  •  Lay insulation layer (polystyrene board, etc.)
  • add reflective film, install PE-RT tube
  • Adjust the spacing, fix the pipe
  • Install the water separator
  • Close with the water separator system
  • corner insulation
  • Pressure test
  • Pouring fine stone concrete cushion
  • pressure test again
  • After passing the test, make the ground surface layer
Brass Heating Manifold
Description:
Brass heating manifolds are sold in 1 to 12 branch pairs for easy assembly in the field. Manifold sections are easily connected together, if more circuits are required. Simply thread two sections together with the use of a manifold coupling and tighten. Make sure the gasket is installed prior to assembly.

 code

pcs/box

pcs/ctn

1F-3/4*2

1

4

1F-3/4*3

1

4

1F-3/4*4

1

4

1F-3/4*5

1

4

1F-3/4*6

1

4

1F-3/4*7

1

4

1F-3/4*8

1

2

1F-3/4*9

1

2

1F-3/4*10

1

2

1F-3/4*11

1

2

1F-3/4*12

1

2

Manufacturing process

Water separator is often used
  1.  In the underfloor heating system, the manifold manages a number of branch pipelines, and is equipped with exhaust valves, automatic thermostatic valves, etc., which are generally made of copper. The caliber is small, between DN25-DN40. There are more imported products.
  2. In the air-conditioning water system, or other industrial water systems, several branch pipelines are also managed, including the backwater branch and the water supply branch, but the larger ones are DN350-DN1500, and they are made of steel plates. Professional manufacturing companies for pressure vessels need to install pressure gauges, thermometers, automatic exhaust valves, safety valves, vent valves, etc. A pressure regulating valve must be installed between the two containers, and an automatic bypass pipeline is required.
  3. In the tap water supply system, the use of water separators effectively avoids loopholes in tap water management, centralized installation and management of water meters, and the use of single pipes and multiple channels reduces the cost of pipe procurement and greatly reduces the construction time. Improved efficiency. The tap water dispenser is directly connected to the aluminum-plastic main pipeline through a reducing diameter, and the water meters are installed in the water meter pool (water meter room) to achieve one meter per household, outdoor installation and outdoor viewing. Currently, household meter reforms are being carried out on a large scale throughout the country.

Construction procedures and technical requirements
  1. Floor elevation leveling and laying line: cleaning the base of the floor and leveling it. The allowable deviation of unevenness is within 8mm
  2. Waterproof layer layout: the ground is wet or the first floor of the building should be laid with heat-insulating and waterproof materials
  3. Lay the reflective layer: PE-RT pipes should be laid on the insulation board with aluminum foil, with the aluminum foil facing up. When laying the insulation board, the ground is required to be flat, and the insulation layer should be taped to the seam.
  4. Lay PE-RT pipes, adjust the spacing, and fix the pipes: on the insulation board, the PE-RT pipes are laid ring by ring from far to near, and the pipes are fixed on the insulation board with a special plastic card (or template). The spacing is not more than 500mm, and the corners are not more than 250mm
  5. Install the manifold and close it with the manifold system: the wall where the manifold is installed should be plastered in advance, and the manifold should be fixed in the wall or in a dedicated alley, and the distance from the ground should be more than 350mm, and away from the heating furnace. The location is close and easy to communicate with the lobby of the room.
  6. ​​Corner insulation: use special corner insulation strips for corner insulation construction
  7. Pressure test: The test pressure should be 1.5 times the working pressure and not less than 0.6MPa. Under the test pressure, stabilize the pressure for 1 hour, the pressure drop should not be greater than 0.05MPa
  8. Pouring fine stone concrete cushion: After passing the pressure test, pour the ground peas concrete cushion in season, and manually wipe and compact it. The pipeline should maintain a pressure of not less than 0.4MPa.
  9. Pressure test again

Taizhou Taisheng Metal Products Co., Ltd.

We are a professional China Ball valve type underfloor heating manifold factory and custom Ball valve type underfloor heating manifold company.The leading product is brass ball valve, brass angle valve, brass globe valve, brass check valve, water divider, brass pipe fittings, stainless steel fittings, hardware fittings.
The company has sophisticated production equipment and advanced testing equipment. We have CE, RoHS and ISO9001 certifications. The company's products are exported to the United States, Germany and other European countries for well-known brand enterprise manufacturers or provide OEM processing. With exquisite craftsmanship and innovative technology, it has been recognized in many aspects.

Feedback

News & Media

Jan 26,2022

The development of valve industry is like a spring breeze, and the upgrading of regulating valve technology has reached a new level

Social development is inseparable from the economic construction of basic industries. Over the past 40 years of reform and opening up, my country's industrial production level has ...

Jan 26,2022

How to tell if a pneumatic valve is easy to use? How should we look at its quality

The existence of our company's pneumatic valve has solved the needs of many users, and its special structure and function are in line with the actual situation. As a result, it is ...

Jan 26,2022

Selection criteria for valve positioners

In many control applications, the valve positioner is one of the important accessories for adjusting the width, especially for a specific application, if you want to choose a suita...

Nov 19,2021

Water conservancy projects serve people's livelihood, which is very important for manufacturers to select high-quality pressure reducing valves

Water conservancy projects are not only important basic projects, but also important livelihood projects. In the construction of various water conservancy projects, the pressure re...

Contact Us

*We respect your confidentiality and all information are protected.